Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Coil clamp for round 12 volt coils

2 required per bike. No longer available new, call us to order used coil clamps

 Sorry, this part is no longer available.

12 volt single lead ignition coil

Suitable for points and Motoplat equipped big twins. NB models with Digiplex ignition use ELA30716. HT lead screws into this HT lead

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14716502 GU14716502 14 71 65 02
 1471 6502 1471.6502 14.71.65.02

Also fits Ducati, MZ ETZ 250/251

3 pin plastic connector for headlight bulb spade connections

No longer available from Guzzi

 Sorry, this part is no longer available.

 17740364 GU17740364 17 74 03 64
 1774 0364 1774.0364 17.74.03.64

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Motoplat ignition unit for one cylinder (2 required per bike)

Also known as Guzzi ref. 23721493, 27721435, 23721491, 23721490, 27721435

 This part is available by special order, request a quote

 23721494 GU23721494 23 72 14 94
 2372 1494 2372.1494 23.72.14.94

Complete right hand Domino switchgear (starter and kill switch) plus twistgrip and pair of handlebar grips

Supplied with 4 pin Molex type connector. Use with ELA27015 to replace earlier Lego switch gear from Le Mans 2, T3 and V50 era models. No longer in production

 Sorry, this part is no longer available.

 27738815 GU27738815 27 73 88 15
 2773 8815 2773.8815 27.73.88.15

Brakelight switch (microswitch) with 2 pin lead

Also see ELA30860

 Availability varies on this part, check availability

 27749815 GU27749815 27 74 98 15
 2774 9815 2774.9815 27.74.98.15

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Ducati regulator rectifier for models fitted with the Ducati charging system

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black male bullet, 1 x red male bullet. See ELA28739 for a less expensive alternative

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05